The screw is installed in the reverse order of removal.
Screw tightening torque: 37±3 Nm.
The screw is installed in the reverse order of removal.
Screw tightening torque: 37±3 Nm.
Removal and installation of the flange screw of fastening of a gear wheel of a balancing shaft
1. Remove the technological plug on the right side of the cylinder block, insert a Phillips screwdriver into the hole formed (to fix the shaft) and unscrew the fixing screw.
The screw is installed in the reverse order of removal.
Screw tightening torque: 37±3 Nm.
The screw is installed in the reverse order of removal.
Screw tightening torque: 37±3 Nm.
This article is available at: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Share with friends:
Removing the oil pan
Removal and installation of the oil pressure sensor
Oil, pump, balancing mechanism and oil pan
Removal and installation of the oil pressure sensor
Oil, pump, balancing mechanism and oil pan
Disassembly and assembly of the oil pump
Replacing the rear bearing of the right balancer shaft
Installing the driven and driving gears and the balance shaft seal
Installing crankshaft seals and front top cover
Oil pan installation
Heat exchanger installation
Oil filter installation
Inspection and testing of parts of the lubrication system
Replacing the rear bearing of the right balancer shaft
Installing the driven and driving gears and the balance shaft seal
Installing crankshaft seals and front top cover
Oil pan installation
Heat exchanger installation
Oil filter installation
Inspection and testing of parts of the lubrication system
Similar materials for other Mitsubishi models
➤ Removal and installation of a gear belt (6А12 DOHC) Mitsubishi Colt 4 and 5 (1991-2003)
➤ Removal and installation of a gear belt of the petrol engine Mitsubishi Lancer 3 and 5 (1984-1992)
➤ Removal and installation of a balancing shaft Mitsubishi Galant 6 and 7 (1987-1998)
➤ Removal and installation of a shaft of a drive of a wheel assy Mitsubishi Outlander 1 (2003-2008)
➤ Front wheel bearing — removal and installation Mitsubishi Pajero 1 and 2 (1982-1999)
➤ Steering wheel and steering shaft — removal and installation Mitsubishi Carisma (1995-2004)
Link in different formats to this article
TEXTHTMLBB Code
Comments and feedback from visitors
No comments yet
- General information
- User manual
- Maintenance
- Power unit
- Diesel engine
- Lubrication system
- Fuel system
- Control system
- Transmission
- Clutch
- Mechanical gearbox
- Transfer case
- Front axle
- Rear axle
- Chassis and running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Doors, locks and windows
- Electrical equipment
- Equipment and devices
- Electrical circuits
MitsubishiMan.ru © 2018–2024 • Mobile version • Articles about Mitsubishi • Contacts • Sitemap: EN BG BY UA RS HR RO PL SK HU • Site search • Bookmark
Colt 2 and 3 (1983-1993) · Colt 4 and 5 (1991-2003) · Colt 5 (1995-2003) · Lancer 3 and 5 (1984-1992) · Lancer 9 (2000-2007) · Galant 6 and 7 (1987-1998) · L200 4 (2005-2014) · Outlander 1 (2003-2008) · Pajero 1 and 2 (1982-1999) · Carisma (1995-2004) · Space Star (1998-2005) ·
Colt 2 and 3 (1983-1993) · Colt 4 and 5 (1991-2003) · Colt 5 (1995-2003) · Lancer 3 and 5 (1984-1992) · Lancer 9 (2000-2007) · Galant 6 and 7 (1987-1998) · L200 4 (2005-2014) · Outlander 1 (2003-2008) · Pajero 1 and 2 (1982-1999) · Carisma (1995-2004) · Space Star (1998-2005) ·